Start a new topic

ProCommander 2 Firmware - Version 2.00

Download the latest version here: 


ProCommander 2 Firmware Update V200



Version 1.88:

 New functions:

 DMX record enabled for devices, which send an universe with less than 512 channels.

 Fixes:

 none.


Version 1.87:

 New functions:

 none.

 Fixes:

 DMX values of FadeDMXValues command mapped to wrong channel.


Version 1.86:

 New functions:

 none.

 Fixes:

 Accumulation of commands to network devices, which are not connected.


Version 1.85:

 New functions:

 Analog read in function implemented.

 Fixes:

 Input check at power up with connected card.


Version 1.84:

 New functions:

 Fade DMX-Values for Conductor Pro implemented.

 Fixes:

 none.


Version 1.83:

 New functions:

 none.

 Fixes:

 Dummy command is included in timecode calculation.


Version 1.81:

 New functions:

 none.

 Fixes:

 Repeat of commands during timecode backward sync.


Version 1.80:

 New functions:

 Automatic switch between RS458 and RS232 on RS232 port 1.

 Fixes:

 none.


Version 1.79:

 New functions:

 Artnet-Monitor ON/OFF during DMX record.

 Activating serial ASCII command input on Rs232-3.

 Fixes:

 none.


Version 1.78:

 New functions:

 Show-End command allows a range of shows, which will be stopped.

 Fixes:

 none.


Version 1.77:

 New functions:

 Implementing of programmable lifetime for MAC stack.

 Fixes:

 none.


Version 1.76:

 New functions:

 Implementing of MAC stack for ProIO.

 Fixes:

 Change in Network management.

 Script can be loaded, even, if other cues are coming in.


Version 1.75:

 New functions:

 none.

 Fixes:

 Longer wait between EEProm write and next EEProm read.

 If write procedure was not finished, a wrong value will come back.


Version 1.74:

 New functions:

 AD-converter prepared for further use.

 Fixes:

 none.


Version 1.73:

 New functions:

 none.

 Fixes:

 Correct write pointer of network chip, if a timeout occures.


Version 1.72:

 New functions:

 none.

 Fixes:

 Wrong handling of modulo function in realtime clock scheduler fixed.


Version 1.71:

 New functions:

 At network watchdog timeout, watchdog-show is not cleared any more.

 Fixes:

 none


Version 1.70:

 New functions:

 A range of variables can be modified at once. E.g.: !vmc1_5=2#

 Fixes:

 none


Version 1.69:

 New functions:

 none

 Fixes:

 VM analog cues made a wrong fetch of IP-Address from ProIO lookup table.

 Wrong feedback display of !sip...# command fixed.


Version 1.68:

 New functions:

 PHX/LX SMPTE-Timecode creation without the need of a running show.

 PHX/LX Start timecode command (!ctc3:00:01:02.10#) allows now to enter a start time for timecode

 Fixes:

 none.


Version 1.67:

 New functions:

 none

 Fixes:

 DMX cues from card for ProIO DMX have not been executed correct.


Version 1.66:

 New functions:

 none

 Fixes:

 Real-time-cues in control.ini have not been executed.


Version 1.65:

 New functions:

 none

 Fixes:

 !gva# created a memory conflict.


Version 1.64:

 New functions:

 none

 Fixes:

 ASCII commands in show from card are sometimes not executed correct.


Version 1.63:

 New functions:

 Additional delay for audio, if show is pauses and continued.

 Fixes:

 none.


Version 1.62:

 New functions:

 DMX from ProCommander to ProIO-DMX via network enabled.

 Fixes:

 none.


Version 1.61:

 New functions:

 TCP-Out and RFID implemented.

 Fixes:

 none.


Version 1.60:

 New functions:

 DMXMergeStart and DMXMergeEnd are checked for useful values.

 Fixes:

 none.


Version 1.59:

 New functions:

 DMXMergeStart and DMXMergeEnd can limit the range where

 DMX values are sent to ProIO devices in !dma1:1# mode.

 Fixes:

 "DMXMap to ProIO" are sent now also via IP.


Version 1.58:

 New functions:

 !gva# command works now also via USB.

 Fixes:

 none.


Version 1.57:

 New functions:

 !gva# implemented.

 Fixes:

 IP-Chip Rest bug fixed.


Version 1.55:

 New functions:

 Basic MIDI-function implemented.

 Network-Bootloader with autoreset on update failure.

 New command !oci0/1# disabling or enabling ip-cues to ProIO devices.

 Fixes:

 none.


Version 1.54:

 New functions:

 New network watchdog features implemented.

 Fixes:

 none.


Version 1.52:

 New functions:

 none.

 Fixes:

 Lockup of IP-chip fixed.


Version 1.51:

 New functions:

 none.

 Fixes:

 Debounce problem for key matrix input fixed.


Version 1.50:

 New functions:

 none.

 Fixes:

 !dxx commands in combination with variable compare commands are not sent to ProIO-devices.


Version 1.49:

 New functions:

 Time code loop through enabled.

 Fixes:

 none.


Version 1.48:

 New functions:

 none.

 Fixes:

 Glitches in audio playback.

 Possible lock up of audio chip fixed.


Version 1.47:

 New functions:

 none.

 Fixes:

 Wrong range in show shuffle start mode.


Version 1.46:

 New functions:

 Get ProIO Sub-ID command included.

 Fixes:

 Repoot, if time code feedback via USB is activated.


Version 1.45:

 New functions:

 Get ProIO Sub-ID command included.

 Fixes:

 none.


Version 1.44:

 New functions:

 Show gaps in shuffle mode are skipped.

 Fixes:

 Analog cues for ProIO device with address 1 are not sent.


Version 1.43:

 New functions:

 none.

 Fixes:

 Fix for ProIO devices.


Version 1.42:

 New functions:

 Show gaps in shuffle mode are skipped.

 Fixes:

 none.


Version 1.41:

 New functions:

 PWM support for ProCommander ES.

 Fixes:

 none.


Version 1.40:

 New functions:

 none.

 Fixes:

 none.


Version 1.39:

 New functions:

 none.

 Fixes:

 IP-lock up, if cues are sent to a ProIO device, which is not connected and Configurator asks for show status.


Version 1.38:

 New functions:

 none.

 Fixes:

 Slow show run, if the audio file can't be found.


Version 1.37:

 New functions:

 none.

 Fixes:

 Network boot loader V110 integrated.


Version 1.36:

 New functions:

 !gsn[:port]# Get show names implemented.

 Fixes:

 Wrong read from slower cards fixed.

 Problem with audio playback after pause solved.


Version 1.35:

 New functions:

 DMX-mapping is possible now for via WEM-NET connected ProIO devices.

 Command for activating ProIO-Mapping:

 !dmd1:20# ProIO Digital with sub-id A1 is mapped to DMX channel 20.

 !dma2:60# ProIO Analog with sub-id A2 is mapped to DMX channel 60.


 TCP-Bootloader implemented.


 The boolean value of all variables compressed in 13 bytes can be queried.

 Command: !vgb# The ProComander returns a 1, if variable is > 0.


 Fixes:

 Playlist problem fixed.


Version 1.34:

 New functions:

 ProIO-Remote can be used in combination with ProCommander.

 Fixes:

 none.


Version 1.33:

 New functions:

 none.

 Fixes:

 If DMX read in is enabled, cues are now sent also to ProIO devices.


Version 1.32:

 New functions:

 Logic functions are now possible with variables.

 Hex-notation can be used with !vmc... command

 !vmc1&0x0001# -> logic AND with value 0x0001 of variable 1.

 !vmc1|0x000A# -> logic OR with value 0x000A of variable 1.

 !vmc1^0x0001# -> logic XOR with value 0x0001 of variable 1.

 Each DMX mix mode (LTP, HTP, Combine,...) can be used for DMX mapping.

 Fixes:

 none.


Version 1.31:

 New functions:

 With activating the DMX-map function (!sdr1#) the DMX merge mode will be switched

 automatically to mode combine, which is required for DMX mapping.

 Command !sdr0# switches back to merge none.

 Fixes:

 !epfl and !epl didn't work with PWM outputs.


Version 1.30:

 New functions:

 none.

 Fixes:

 In V1.29 PWM channels overwrite DMX channels if ConductorPro is used for programming.


Version 1.29:

 New functions:

 Watchdog command implemented.

 Fixes:

 none.


Versions skipped, due to have unique version numbers for all ProCommander.


Version 1.28:

 New functions:

 Shows can be started in shuffle mode. Command: !rss1_10# starts a show between 1 and 10

 Fixes:

 PWM commands didn't work with VenueMagic.

 Cues for ProIO devices are droped, if one ProIO device is not present in a network setup.


Version 1.27:

 New functions:

 none.

 Fixes:

 ASCII-Strings in Control.ini related to inputs has been interpreted wrong.

 Cues for ProIO devices are droped, if one ProIO device is not present in a network setup.


Version 1.26:

 New functions:

 Internal changes

 Fixes:

 none.


Version 1.25:

 New functions:

 Key matrix implemented for ProCommander ES (Activate: !skm1#, deactivate: !skm0#)

 Fixes:

 none.


Version 1.24:

 New functions:

 none

 Fixes:

 Audio drop out with interrupted shows.


Version 1.22:

 New functions:

 none

 Fixes:

 Audio is delayed, if the new audio sample will be started within a certain time after the previous audio has stopped.


Version 1.21:

 New functions:

 Set master volume allows now +/- as parameter and the new incremented or decremented value will be stored.

 Set master volume 33 (!smv33#) stores current volume level.

 Fixes:

 A running show in combination with control.ini could cause a wrong reading of control.ini


Version 1.20:

 New functions:

 none.

 Fixes:

 IP-Address for ProIO-devices was wrong..


Version 1.19:

 New functions:

 none.

 Fixes:

 Changes did not affect ProCommander LX.


Version 1.18:

 New functions:

 none.

 Fixes:

 Changes did not affect ProCommander LX.


Version 1.17:

 New functions:

 Enable of multiple DMX universe via WEM-NET.

 Fixes:

 none.


Version 1.16:

 New functions:

 Internal changes.

 Fixes:

 none.


Version 1.15:

 New functions:

 Additional diasy chain baud rates: 400000 and 500000 baud.

 With !gdb# you can ask for the current daisy chain baud rate.

 Fixes:

 PWM8 (output 16) didn't work.

 Feedback message of volume bass and treble setting was wrong.


Version 1.14:

 New functions:

 Shownumbers can have now up to 4 leading zeros. Maximum number of characters is limited to 5.

 allowed is: !rsn1# or !rsn01# or !rsn001# or !rsn0001# or !rsn00001#.

 Fixes:

 Show-Pause function reenabled.

 Lock-up of MP3 chip during interrupt of soundtrack fixed.


Version 1.13:

 New functions:

 none.

 Fixes:

 Changes in playlist playback. Audio on a channel locks up, if audio on an other channel has the same length.


Version 1.12:

 New functions:

 VU-meter can be switched off with command !ovu0# (!ovu1# is the command for switch on).

 Fixes:

 Change of IP-Address in menu has not been stored.


Version 1.11:

 New functions:

 Implementing of GetVolume, GetBass and GetTreble commands.

 Fixes:

 none.


Version 1.10:

 New functions:

 none.

 Fixes:

 Variable commands did not work.


Version 1.09:

 New functions:

 none.

 Fixes:

 audio channel stoped working or glitched complete new file,

 if new audio track with different sampling rate was started,

 before previous audio file has been finished.


Version 1.08:

 New functions:

 none.

 Fixes:

 lock-up, if rtcc commands are used in a longer Control.ini file


Version 1.07:

 New functions:

 DMX-Input can be used to trigger events in Control.ini.

e.g.: !d1=100!rsn1# if dmx channel 1 gets value 100, run show 1.

 Max. DMX-Events: 32.


 RTCC-Events in Control.ini have been enabled.

 Max. RTCC_events: 128.

 Fixes:

 none.


Version 1.06:

 New functions:

 New menu setting: Ignore Start Clear [ON..OFF].

 Fixes:

 Some problems in menu handling.


Version 1.05:

 New functions:

 None.

 Fixes:

 !sdb1:....# (Set Daisy Chain Baudrate) command was not sent via network to ProIO devices.


Version 1.04:

 New functions:

 Individual Volume, Bass and Treble settings for each channel in menu and via ASCII-commands.

 Volume store on button press within 2 seconds after volume change.

 New analog level set command for VenueMagic.

 Selectable amplifier gain for audio power amplifier.

 Increasing possible baud rate for WEM-NET to 250kB.

 Fixes:

 None.

 

Version 1.03:

 New functions:

 DIO32 compatible mode is implemented now.

 Fixes:

 Unit comes back with the "WEMC-1" string to be compatible with the current version of VM.


Version 1.00:

 New functions:

 Start-Version

 Fixes:

 None.

Login or Signup to post a comment